ugfx/drivers/ginput/touch/FT5x06/ginput_lld_mouse.c

119 lines
2.9 KiB
C
Raw Normal View History

2013-06-22 03:00:48 +00:00
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
2013-07-21 20:20:37 +00:00
* http://ugfx.org/license.html
2013-06-22 03:00:48 +00:00
*/
/**
* @file drivers/ginput/touch/STMPE811/ginput_lld_mouse.c
* @brief GINPUT Touch low level driver source for the STMPE811.
*
* @defgroup Mouse Mouse
* @ingroup GINPUT
* @{
*/
#include "gfx.h"
#if (GFX_USE_GINPUT && GINPUT_NEED_MOUSE) /*|| defined(__DOXYGEN__)*/
#include "src/ginput/driver_mouse.h"
#include "drivers/ginput/touch/FT5x06/ft5x06.h"
2013-06-22 03:00:48 +00:00
// include board abstraction
#include "ginput_lld_mouse_board.h"
static coord_t x, y, z;
static uint8_t touched;
/**
* @brief Initialise the mouse/touch.
*
* @notapi
*/
void ginput_lld_mouse_init(void) {
init_board();
// Init default values. (From NHD-3.5-320240MF-ATXL-CTP-1 datasheet)
// Valid touching detect threshold
write_reg(FT5x06_ID_G_THGROUP, 1, 0x16);
// valid touching peak detect threshold
write_reg(FT5x06_ID_G_THPEAK, 1, 0x3C);
// Touch focus threshold
write_reg(FT5x06_ID_G_THCAL, 1, 0xE9);
// threshold when there is surface water
write_reg(FT5x06_ID_G_THWATER, 1, 0x01);
// threshold of temperature compensation
write_reg(FT5x06_ID_G_THTEMP, 1, 0x01);
// Touch difference threshold
write_reg(FT5x06_ID_G_THDIFF, 1, 0xA0);
// Delay to enter 'Monitor' status (s)
write_reg(FT5x06_ID_G_TIME_ENTER_MONITOR, 1, 0x0A);
// Period of 'Active' status (ms)
write_reg(FT5x06_ID_G_PERIODACTIVE, 1, 0x06);
// Timer to enter <20>idle<6C> when in 'Monitor' (ms)
write_reg(FT5x06_ID_G_PERIODMONITOR, 1, 0x28);
}
/**
* @brief Read the mouse/touch position.
*
* @param[in] pt A pointer to the structure to fill
*
* @note For drivers that don't support returning a position
* when the touch is up (most touch devices), it should
* return the previous position with the new Z value.
* The z value is the pressure for those touch devices
* that support it (-100 to 100 where > 0 is touched)
* or, 0 or 100 for those drivers that don't.
*
* @notapi
*/
void ginput_lld_mouse_get_reading(MouseReading *pt) {
// Poll to get the touched status
uint8_t last_touched;
last_touched = touched;
touched = (uint8_t)read_reg(FT5x06_TOUCH_POINTS, 1) & 0x07;
// If not touched, return the previous results
if (touched == 0) {
pt->x = x;
pt->y = y;
pt->z = 0;
pt->buttons = 0;
return;
}
/* Get the X, Y, Z values */
x = (coord_t)(read_reg(FT5x06_TOUCH1_XH, 2) & 0x0fff);
y = (coord_t)read_reg(FT5x06_TOUCH1_YH, 2);
z = 100;
// Rescale X,Y,Z - X & Y don't need scaling when you are using calibration!
#if !GINPUT_MOUSE_NEED_CALIBRATION
x = gdispGetWidth() - x / (4096/gdispGetWidth());
y = y / (4096/gdispGetHeight());
#endif
// Return the results. ADC gives values from 0 to 2^12 (4096)
pt->x = x;
pt->y = y;
pt->z = z;
pt->buttons = GINPUT_TOUCH_PRESSED;
}
#endif /* GFX_USE_GINPUT && GINPUT_NEED_MOUSE */
/** @} */