ugfx/boards/addons/gdisp/board_SSD1306_spi.h

134 lines
3.3 KiB
C
Raw Normal View History

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/gdisp/SSD1306/board_SSD1306_spi.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// The command byte to put on the front of each page line
#define SSD1306_PAGE_PREFIX 0x40 // Co = 0, D/C = 1
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
#define SSD1306_RESET_PORT GPIOB
#define SSD1306_RESET_PIN 5
#define SSD1306_MISO_PORT GPIOB
#define SSD1306_MISO_PIN 8
#define SSD1306_MOSI_PORT GPIOB
#define SSD1306_MOSI_PIN 7
#define SSD1306_SCK_PORT GPIOB
#define SSD1306_SCK_PIN 6
#define SSD1306_CS_PORT GPIOB
#define SSD1306_CS_PIN 5
#define SET_RST palSetPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
#define CLR_RST palClearPad(SSD1306_RESET_PORT, SSD1306_RESET_PIN);
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1config = {
0,
/* HW dependent part.*/
SSD1306_MISO_PORT,
SSD1306_MISO_PIN,
0
//SPI_CR1_BR_0
};
#if GFX_USE_OS_CHIBIOS
static int32_t thdPriority = 0;
#endif
static inline void init_board(GDisplay *g) {
unsigned i;
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
// RESET pin.
palSetPadMode(SSD1306_RESET_PORT, SSD1306_RESET_PIN, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(SSD1306_MISO_PORT, SSD1306_MISO_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_MOSI_PORT, SSD1306_MOSI_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPadMode(SSD1306_SCK_PORT, SSD1306_SCK_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
palSetPad(SSD1306_CS_PORT, SSD1306_CS_PIN);
palSetPadMode(SSD1306_CS_PORT, SSD1306_CS_PIN, PAL_MODE_ALTERNATE(1)|
PAL_STM32_OSPEED_HIGHEST);
spiInit();
break;
}
}
static inline void post_init_board(GDisplay *g) {
(void) g;
}
static inline void setpin_reset(GDisplay *g, bool_t state) {
(void) g;
if(state)
CLR_RST
else
SET_RST
}
static inline void acquire_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
thdPriority = (int32_t)chThdGetPriority();
chThdSetPriority(HIGHPRIO);
#endif
spiAcquireBus(&SPID1);
}
static inline void release_bus(GDisplay *g) {
(void) g;
#if GFX_USE_OS_CHIBIOS
chThdSetPriority(thdPriority);
#endif
spiReleaseBus(&SPID1);
}
static inline void write_cmd(GDisplay *g, uint8_t cmd) {
uint8_t command[2];
2013-11-06 07:21:58 +00:00
(void) g;
command[0] = 0x00; // Co = 0, D/C = 0
command[1] = cmd;
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, 2, command);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
static inline void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
(void) g;
spiStart(&SPID1, &spi1config);
spiSelect(&SPID1);
spiStartSend(&SPID1, length, data);
spiUnselect(&SPID1);
spiStop(&SPID1);
}
#endif /* _GDISP_LLD_BOARD_H */