/* ChibiOS/GFX - Copyright (C) 2012 Joel Bodenmann aka Tectu This file is part of ChibiOS/GFX. ChibiOS/GFX is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 3 of the License, or (at your option) any later version. ChibiOS/GFX is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ /** * @file drivers/gdisp/Nokia6610/gdisp_lld_board_olimexsam7ex256.h * @brief GDISP Graphic Driver subsystem board interface for the Olimex SAM7-EX256 board. * * @addtogroup GDISP * @{ */ #ifndef _GDISP_LLD_BOARD_H #define _GDISP_LLD_BOARD_H // ****************************************************** // Pointers to AT91SAM7X256 peripheral data structures // ****************************************************** volatile AT91PS_PIO pPIOA = AT91C_BASE_PIOA; volatile AT91PS_PIO pPIOB = AT91C_BASE_PIOB; volatile AT91PS_SPI pSPI = AT91C_BASE_SPI0; volatile AT91PS_PMC pPMC = AT91C_BASE_PMC; volatile AT91PS_PDC pPDC = AT91C_BASE_PDC_SPI0; /** * @brief Initialise the board for the display. * @notes Performs the following functions: * 1. initialise the spi port used by your display * 2. initialise the reset pin (initial state not-in-reset) * 3. initialise the chip select pin (initial state not-active) * 4. initialise the backlight pin (initial state back-light off) * * @notapi */ static __inline void init_board(void) { // ********************************************************************************************* // InitSpi( ) // // Sets up SPI channel 0 for communications to Nokia 6610 LCD Display // // I/O ports used: PA2 = LCD Reset (set to low to reset) // PA12 = LCD chip select (set to low to select the LCD chip) // PA16 = SPI0_MISO Master In - Slave Out (not used in LCD interface) // PA17 = SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave) // PA18 = SPI0_SPCK Serial Clock (to LCD slave) // PB20 = backlight control (normally PWM control, 1 = full on) // // *********************************************************************************************} /* This code should really use the ChibiOS driver for these functions */ // Pin for backlight pPIOB->PIO_CODR = PIOB_LCD_BL_MASK; // Set PB20 to LOW pPIOB->PIO_OER = PIOB_LCD_BL_MASK; // Configure PB20 as output // Reset pin pPIOA->PIO_SODR = PIOA_LCD_RESET_MASK; // Set PA2 to HIGH pPIOA->PIO_OER = PIOA_LCD_RESET_MASK; // Configure PA2 as output // CS pin - this seems to be ignored // pPIOA->PIO_SODR = 1<<12; // Set PA2 to HIGH // pPIOA->PIO_OER = 1<<12; // Configure PA2 as output // Init SPI0 // Disable the following pins from PIO control (will be used instead by the SPI0 peripheral) // BIT12 = PA12 -> SPI0_NPCS0 chip select // BIT16 = PA16 -> SPI0_MISO Master In - Slave Out (not used in LCD interface) // BIT17 = PA17 -> SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave) // BIT18 = PA18 -> SPI0_SPCK Serial Clock (to LCD slave) pPIOA->PIO_PDR = (1<<12) | (1<<16) | (1<<17) | (1<<18); pPIOA->PIO_ASR = (1<<12) | (1<<16) | (1<<17) | (1<<18); pPIOA->PIO_BSR = 0; //enable the clock of SPI pPMC->PMC_PCER = 1 << AT91C_ID_SPI0; // Fixed mode pSPI->SPI_CR = 0x81; //SPI Enable, Sowtware reset pSPI->SPI_CR = 0x01; //SPI Enable //pSPI->SPI_MR = 0xE0019; //Master mode, fixed select, disable decoder, FDIV=1 (MCK), PCS=1110 pSPI->SPI_MR = 0xE0011; //Master mode, fixed select, disable decoder, FDIV=0 (MCK), PCS=1110 //pSPI->SPI_CSR[0] = 0x01010C11; //9bit, CPOL=1, ClockPhase=0, SCLK = 48Mhz/32*12 = 125kHz pSPI->SPI_CSR[0] = 0x01010311; //9bit, CPOL=1, ClockPhase=0, SCLK = 48Mhz/8 = 6MHz if using commented MR line above } /** * @brief Set or clear the lcd reset pin. * * @param[in] state TRUE = lcd in reset, FALSE = normal operation * * @notapi */ static __inline void setpin_reset(bool_t state) { if (state) palClearPad(IOPORT1, PIOA_LCD_RESET); else palSetPad(IOPORT1, PIOA_LCD_RESET); } /** * @brief Set the lcd back-light level. * @note For now 0% turns the backlight off, anything else the backlight is on. * While the hardware supports PWM backlight control, we are not using it * yet. * * @param[in] percent 0 to 100% * * @notapi */ static __inline void set_backlight(uint8_t percent) { if (percent) palSetPad(IOPORT2, PIOB_LCD_BL); else palClearPad(IOPORT2, PIOB_LCD_BL); } /** * @brief Take exclusive control of the bus * * @notapi */ static __inline void acquire_bus(void) { /* Nothing to do for this board as the LCD is the only device on the SPI port */ } /** * @brief Release exclusive control of the bus * * @notapi */ static __inline void release_bus(void) { // Nothing to do for this board as the LCD is the only device on the SPI port } /** * @brief Send an 8 bit command to the lcd. * * @param[in] cmd The command to send * * @notapi */ static __inline void write_cmd(uint16_t cmd) { // wait for the previous transfer to complete while((pSPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0); // send the command pSPI->SPI_TDR = cmd & 0xFF; } /** * @brief Send an 8 bit data to the lcd. * * @param[in] data The data to send * * @notapi */ static __inline void write_data(uint16_t data) { // wait for the previous transfer to complete while((pSPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0); // send the data pSPI->SPI_TDR = data | 0x0100; } #if GDISP_HARDWARE_READPIXEL || GDISP_HARDWARE_SCROLL || defined(__DOXYGEN__) /** * @brief Read data from the lcd. * * @return The data from the lcd * * @notapi */ static __inline uint16_t read_data(void) { #error "gdispNokia6610: GDISP_HARDWARE_READPIXEL and GDISP_HARDWARE_SCROLL are not supported on this board" return 0; } #endif #endif /* _GDISP_LLD_BOARD_H */ /** @} */