ugfx/drivers/gdisp/SSD1306/gdisp_lld_SSD1306.c

283 lines
7.8 KiB
C

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/gdisp/SSD1306/gdisp_lld.c
* @brief GDISP Graphics Driver subsystem low level driver source for the SSD1306 display.
*/
#include "gfx.h"
#if GFX_USE_GDISP
#define GDISP_DRIVER_VMT GDISPVMT_SSD1306
#include "drivers/gdisp/SSD1306/gdisp_lld_config.h"
#include "src/gdisp/driver.h"
#include "board_SSD1306.h"
/*===========================================================================*/
/* Driver local definitions. */
/*===========================================================================*/
#ifndef GDISP_SCREEN_HEIGHT
#define GDISP_SCREEN_HEIGHT 64 // This controller should support 32 (untested) or 64
#endif
#ifndef GDISP_SCREEN_WIDTH
#define GDISP_SCREEN_WIDTH 128
#endif
#ifndef GDISP_INITIAL_CONTRAST
#define GDISP_INITIAL_CONTRAST 100
#endif
#ifndef GDISP_INITIAL_BACKLIGHT
#define GDISP_INITIAL_BACKLIGHT 100
#endif
#ifdef SSD1306_PAGE_PREFIX
#define SSD1306_PAGE_WIDTH (GDISP_SCREEN_WIDTH+1)
#define SSD1306_PAGE_OFFSET 1
#else
#define SSD1306_PAGE_WIDTH GDISP_SCREEN_WIDTH
#define SSD1306_PAGE_OFFSET 0
#endif
#define GDISP_FLG_NEEDFLUSH (GDISP_FLG_DRIVER<<0)
#include "drivers/gdisp/SSD1306/SSD1306.h"
/*===========================================================================*/
/* Driver local functions. */
/*===========================================================================*/
// Some common routines and macros
#define RAM(g) ((uint8_t *)g->priv)
#define write_cmd2(g, cmd1, cmd2) { write_cmd(g, cmd1); write_cmd(g, cmd2); }
#define write_cmd3(g, cmd1, cmd2, cmd3) { write_cmd(g, cmd1); write_cmd(g, cmd2); write_cmd(g, cmd3); }
// Some common routines and macros
#define delay(us) gfxSleepMicroseconds(us)
#define delayms(ms) gfxSleepMilliseconds(ms)
#define xyaddr(x, y) (SSD1306_PAGE_OFFSET + (x) + ((y)>>3)*SSD1306_PAGE_WIDTH)
#define xybit(y) (1<<((y)&7))
/*===========================================================================*/
/* Driver exported functions. */
/*===========================================================================*/
/**
* As this controller can't update on a pixel boundary we need to maintain the
* the entire display surface in memory so that we can do the necessary bit
* operations. Fortunately it is a small display in monochrome.
* 64 * 128 / 8 = 1024 bytes.
*/
LLDSPEC bool_t gdisp_lld_init(GDisplay *g) {
// The private area is the display surface.
g->priv = gfxAlloc(GDISP_SCREEN_HEIGHT/8 * SSD1306_PAGE_WIDTH);
// Fill in the prefix command byte on each page line of the display buffer
// We can do it during initialisation as this byte is never overwritten.
#ifdef SSD1306_PAGE_PREFIX
{
unsigned i;
for(i=0; i < GDISP_SCREEN_HEIGHT/8 * SSD1306_PAGE_WIDTH; i+=SSD1306_PAGE_WIDTH)
RAM(g)[i] = SSD1306_PAGE_PREFIX;
}
#endif
// Initialise the board interface
init_board(g);
// Hardware reset
setpin_reset(g, TRUE);
gfxSleepMilliseconds(20);
setpin_reset(g, FALSE);
gfxSleepMilliseconds(20);
acquire_bus(g);
write_cmd(g, SSD1306_DISPLAYOFF);
write_cmd2(g, SSD1306_SETDISPLAYCLOCKDIV, 0x80);
write_cmd2(g, SSD1306_SETMULTIPLEX, GDISP_SCREEN_HEIGHT-1);
write_cmd2(g, SSD1306_SETPRECHARGE, 0x1F);
write_cmd2(g, SSD1306_SETDISPLAYOFFSET, 0);
write_cmd(g, SSD1306_SETSTARTLINE | 0);
write_cmd2(g, SSD1306_ENABLE_CHARGE_PUMP, 0x14);
write_cmd2(g, SSD1306_MEMORYMODE, 0);
write_cmd(g, SSD1306_SEGREMAP+1);
write_cmd(g, SSD1306_COMSCANDEC);
#if GDISP_SCREEN_HEIGHT == 64
write_cmd2(g, SSD1306_SETCOMPINS, 0x12);
#else
write_cmd2(g, SSD1306_SETCOMPINS, 0x22);
#endif
write_cmd2(g, SSD1306_SETCONTRAST, (uint8_t)(GDISP_INITIAL_CONTRAST*256/101)); // Set initial contrast.
write_cmd2(g, SSD1306_SETVCOMDETECT, 0x10);
write_cmd(g, SSD1306_DISPLAYON);
write_cmd(g, SSD1306_NORMALDISPLAY);
write_cmd3(g, SSD1306_HV_COLUMN_ADDRESS, 0, GDISP_SCREEN_WIDTH-1);
write_cmd3(g, SSD1306_HV_PAGE_ADDRESS, 0, GDISP_SCREEN_HEIGHT/8-1);
// Finish Init
post_init_board(g);
// Release the bus
release_bus(g);
/* Initialise the GDISP structure */
g->g.Width = GDISP_SCREEN_WIDTH;
g->g.Height = GDISP_SCREEN_HEIGHT;
g->g.Orientation = GDISP_ROTATE_0;
g->g.Powermode = powerOn;
g->g.Backlight = GDISP_INITIAL_BACKLIGHT;
g->g.Contrast = GDISP_INITIAL_CONTRAST;
return TRUE;
}
#if GDISP_HARDWARE_FLUSH
LLDSPEC void gdisp_lld_flush(GDisplay *g) {
unsigned i;
// Don't flush if we don't need it.
if (!(g->flags & GDISP_FLG_NEEDFLUSH))
return;
write_cmd(g, SSD1306_SETSTARTLINE | 0);
for(i=0; i < GDISP_SCREEN_HEIGHT/8 * SSD1306_PAGE_WIDTH; i+=SSD1306_PAGE_WIDTH)
write_data(g, RAM(g)+i, SSD1306_PAGE_WIDTH);
}
#endif
#if GDISP_HARDWARE_DRAWPIXEL
LLDSPEC void gdisp_lld_draw_pixel(GDisplay *g) {
coord_t x, y;
switch(g->g.Orientation) {
default:
case GDISP_ROTATE_0:
x = g->p.x;
y = g->p.y;
break;
case GDISP_ROTATE_90:
x = g->p.y;
y = GDISP_SCREEN_HEIGHT-1 - g->p.x;
break;
case GDISP_ROTATE_180:
x = GDISP_SCREEN_WIDTH-1 - g->p.x;
y = GDISP_SCREEN_HEIGHT-1 - g->p.y;
break;
case GDISP_ROTATE_270:
x = GDISP_SCREEN_HEIGHT-1 - g->p.y;
x = g->p.x;
break;
}
if (gdispColor2Native(g->p.color) != Black)
RAM(g)[xyaddr(x, y)] |= xybit(y);
else
RAM(g)[xyaddr(x, y)] &= ~xybit(y);
g->flags |= GDISP_FLG_NEEDFLUSH;
}
#endif
#if GDISP_HARDWARE_PIXELREAD
LLDSPEC color_t gdisp_lld_get_pixel_color(GDisplay *g) {
coord_t x, y;
switch(g->g.Orientation) {
default:
case GDISP_ROTATE_0:
x = g->p.x;
y = g->p.y;
break;
case GDISP_ROTATE_90:
x = g->p.y;
y = GDISP_SCREEN_HEIGHT-1 - g->p.x;
break;
case GDISP_ROTATE_180:
x = GDISP_SCREEN_WIDTH-1 - g->p.x;
y = GDISP_SCREEN_HEIGHT-1 - g->p.y;
break;
case GDISP_ROTATE_270:
x = GDISP_SCREEN_HEIGHT-1 - g->p.y;
y = g->p.x;
break;
}
return (RAM(g)[xyaddr(x, y)] & xybit(y)) ? White : Black;
}
#endif
#if GDISP_NEED_CONTROL && GDISP_HARDWARE_CONTROL
LLDSPEC void gdisp_lld_control(GDisplay *g) {
switch(g->p.x) {
case GDISP_CONTROL_POWER:
if (g->g.Powermode == (powermode_t)g->p.ptr)
return;
switch((powermode_t)g->p.ptr) {
case powerOff:
case powerSleep:
case powerDeepSleep:
acquire_bus(g);
write_cmd(g, SSD1306_DISPLAYOFF);
release_bus(g);
break;
case powerOn:
acquire_bus(g);
write_cmd(g, SSD1306_DISPLAYON);
release_bus(g);
break;
default:
return;
}
g->g.Powermode = (powermode_t)g->p.ptr;
return;
case GDISP_CONTROL_ORIENTATION:
if (g->g.Orientation == (orientation_t)g->p.ptr)
return;
switch((orientation_t)g->p.ptr) {
/* Rotation is handled by the drawing routines */
case GDISP_ROTATE_0:
case GDISP_ROTATE_180:
g->g.Height = GDISP_SCREEN_HEIGHT;
g->g.Width = GDISP_SCREEN_WIDTH;
break;
case GDISP_ROTATE_90:
case GDISP_ROTATE_270:
g->g.Height = GDISP_SCREEN_WIDTH;
g->g.Width = GDISP_SCREEN_HEIGHT;
break;
default:
return;
}
g->g.Orientation = (orientation_t)g->p.ptr;
return;
case GDISP_CONTROL_CONTRAST:
if ((unsigned)g->p.ptr > 100)
g->p.ptr = (void *)100;
acquire_bus(g);
write_cmd2(g, SSD1306_SETCONTRAST, (((unsigned)g->p.ptr)<<8)/101);
release_bus(g);
g->g.Contrast = (unsigned)g->p.ptr;
return;
// Our own special controller code to inverse the display
// 0 = normal, 1 = inverse
case GDISP_CONTROL_INVERSE:
acquire_bus(g);
write_cmd(g, g->p.ptr ? SSD1306_INVERTDISPLAY : SSD1306_NORMALDISPLAY);
release_bus(g);
return;
}
}
#endif // GDISP_NEED_CONTROL
#endif // GFX_USE_GDISP