uGFX/ugfx
2
0
Fork 0
Code Issues 2 Pull Requests Projects Releases Wiki Activity
701ff38230
ugfx/drivers/gdisp/SSD1289/gdisp_lld.c
Joel Bodenmann f14ed21d5d SSD1289 update by user Eddie
2013-06-04 00:34:47 +02:00

648 lines
21 KiB
C
Raw Blame History

/*
* This file is subject to the terms of the GFX License, v1.0. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://chibios-gfx.com/license.html
*/
/**
* @file drivers/gdisp/SSD1289/gdisp_lld.c
* @brief GDISP Graphics Driver subsystem low level driver source for the SSD1289 display.
*
* @addtogroup GDISP
* @{
*/
#include "gfx.h"
#if GFX_USE_GDISP /*|| defined(__DOXYGEN__)*/
/* Include the emulation code for things we don't support */
#include "gdisp/lld/emulation.c"
/*===========================================================================*/
/* Driver local definitions. */
/*===========================================================================*/
#ifndef GDISP_SCREEN_HEIGHT
#define GDISP_SCREEN_HEIGHT 320
#endif
#ifndef GDISP_SCREEN_WIDTH
#define GDISP_SCREEN_WIDTH 240
#endif
#define GDISP_INITIAL_CONTRAST 50
#define GDISP_INITIAL_BACKLIGHT 100
/*===========================================================================*/
/* Driver local functions. */
/*===========================================================================*/
#if defined(GDISP_USE_CUSTOM_BOARD) && GDISP_USE_CUSTOM_BOARD
/* Include the user supplied board definitions */
#include "gdisp_lld_board.h"
#elif defined(BOARD_FIREBULL_STM32_F103)
#include "gdisp_lld_board_firebullstm32f103.h"
#elif defined(BOARD_ST_STM32F4_DISCOVERY)
#include "gdisp_lld_board_st_stm32f4_discovery.h"
#else
/* Include the user supplied board definitions */
#include "gdisp_lld_board.h"
#endif
// Some common routines and macros
#define write_reg(reg, data) { write_index(reg); write_data(data); }
#define stream_start() write_index(0x0022);
#define stream_stop()
#define delay(us) gfxSleepMicroseconds(us)
#define delayms(ms) gfxSleepMilliseconds(ms)
static inline void set_cursor(coord_t x, coord_t y) {
/* Reg 0x004E is an 8 bit value
* Reg 0x004F is 9 bit
* Use a bit mask to make sure they are not set too high
*/
switch(GDISP.Orientation) {
case GDISP_ROTATE_180:
write_reg(0x004e, (GDISP_SCREEN_WIDTH-1-x) & 0x00FF);
write_reg(0x004f, (GDISP_SCREEN_HEIGHT-1-y) & 0x01FF);
break;
case GDISP_ROTATE_0:
write_reg(0x004e, x & 0x00FF);
write_reg(0x004f, y & 0x01FF);
break;
case GDISP_ROTATE_270:
write_reg(0x004e, y & 0x00FF);
write_reg(0x004f, x & 0x01FF);
break;
case GDISP_ROTATE_90:
write_reg(0x004e, (GDISP_SCREEN_WIDTH - y - 1) & 0x00FF);
write_reg(0x004f, (GDISP_SCREEN_HEIGHT - x - 1) & 0x01FF);
break;
}
}
static void set_viewport(coord_t x, coord_t y, coord_t cx, coord_t cy) {
//set_cursor(x, y);
/* Reg 0x44 - Horizontal RAM address position
* Upper Byte - HEA
* Lower Byte - HSA
* 0 <= HSA <= HEA <= 0xEF
* Reg 0x45,0x46 - Vertical RAM address position
* Lower 9 bits gives 0-511 range in each value
* 0 <= Reg(0x45) <= Reg(0x46) <= 0x13F
*/
switch(GDISP.Orientation) {
case GDISP_ROTATE_0:
write_reg(0x44, (((x+cx-1) << 8) & 0xFF00 ) | (x & 0x00FF));
write_reg(0x45, y & 0x01FF);
write_reg(0x46, (y+cy-1) & 0x01FF);
break;
case GDISP_ROTATE_270:
write_reg(0x44, (((x+cx-1) << 8) & 0xFF00 ) | (y & 0x00FF));
write_reg(0x45, x & 0x01FF);
write_reg(0x46, (x+cx-1) & 0x01FF);
break;
case GDISP_ROTATE_180:
write_reg(0x44, (((GDISP_SCREEN_WIDTH-x-1) & 0x00FF) << 8) | ((GDISP_SCREEN_WIDTH - (x+cx)) & 0x00FF));
write_reg(0x45, (GDISP_SCREEN_HEIGHT-(y+cy)) & 0x01FF);
write_reg(0x46, (GDISP_SCREEN_HEIGHT-y-1) & 0x01FF);
break;
case GDISP_ROTATE_90:
write_reg(0x44, (((GDISP_SCREEN_WIDTH - y - 1) & 0x00FF) << 8) | ((GDISP_SCREEN_WIDTH - (y+cy)) & 0x00FF));
write_reg(0x45, (GDISP_SCREEN_HEIGHT - (x+cx)) & 0x01FF);
write_reg(0x46, (GDISP_SCREEN_HEIGHT - x - 1) & 0x01FF);
break;
}
set_cursor(x, y);
}
static inline void reset_viewport(void) {
set_viewport(0, 0, GDISP.Width, GDISP.Height);
}
/*===========================================================================*/
/* Driver interrupt handlers. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver exported functions. */
/*===========================================================================*/
/* ---- Required Routines ---- */
/*
The following 2 routines are required.
All other routines are optional.
*/
/**
* @brief Low level GDISP driver initialization.
*
* @notapi
*/
bool_t gdisp_lld_init(void) {
/* Initialise your display */
init_board();
// Hardware reset
setpin_reset(TRUE);
delayms(20);
setpin_reset(FALSE);
delayms(20);
// Get the bus for the following initialisation commands
acquire_bus();
write_reg(0x0000,0x0001); delay(5);
write_reg(0x0003,0xA8A4); delay(5);
write_reg(0x000C,0x0000); delay(5);
write_reg(0x000D,0x080C); delay(5);
write_reg(0x000E,0x2B00); delay(5);
write_reg(0x001E,0x00B0); delay(5);
write_reg(0x0001,0x2B3F); delay(5);
write_reg(0x0002,0x0600); delay(5);
write_reg(0x0010,0x0000); delay(5);
write_reg(0x0011,0x6070); delay(5);
write_reg(0x0005,0x0000); delay(5);
write_reg(0x0006,0x0000); delay(5);
write_reg(0x0016,0xEF1C); delay(5);
write_reg(0x0017,0x0003); delay(5);
write_reg(0x0007,0x0133); delay(5);
write_reg(0x000B,0x0000); delay(5);
write_reg(0x000F,0x0000); delay(5);
write_reg(0x0041,0x0000); delay(5);
write_reg(0x0042,0x0000); delay(5);
write_reg(0x0048,0x0000); delay(5);
write_reg(0x0049,0x013F); delay(5);
write_reg(0x004A,0x0000); delay(5);
write_reg(0x004B,0x0000); delay(5);
write_reg(0x0044,0xEF00); delay(5);
write_reg(0x0045,0x0000); delay(5);
write_reg(0x0046,0x013F); delay(5);
write_reg(0x0030,0x0707); delay(5);
write_reg(0x0031,0x0204); delay(5);
write_reg(0x0032,0x0204); delay(5);
write_reg(0x0033,0x0502); delay(5);
write_reg(0x0034,0x0507); delay(5);
write_reg(0x0035,0x0204); delay(5);
write_reg(0x0036,0x0204); delay(5);
write_reg(0x0037,0x0502); delay(5);
write_reg(0x003A,0x0302); delay(5);
write_reg(0x003B,0x0302); delay(5);
write_reg(0x0023,0x0000); delay(5);
write_reg(0x0024,0x0000); delay(5);
write_reg(0x0025,0x8000); delay(5);
write_reg(0x004f,0x0000); delay(5);
write_reg(0x004e,0x0000); delay(5);
// Release the bus
release_bus();
/* Turn on the back-light */
set_backlight(GDISP_INITIAL_BACKLIGHT);
/* Initialise the GDISP structure */
GDISP.Width = GDISP_SCREEN_WIDTH;
GDISP.Height = GDISP_SCREEN_HEIGHT;
GDISP.Orientation = GDISP_ROTATE_0;
GDISP.Powermode = powerOn;
GDISP.Backlight = GDISP_INITIAL_BACKLIGHT;
GDISP.Contrast = GDISP_INITIAL_CONTRAST;
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
GDISP.clipx0 = 0;
GDISP.clipy0 = 0;
GDISP.clipx1 = GDISP.Width;
GDISP.clipy1 = GDISP.Height;
#endif
return TRUE;
}
/**
* @brief Draws a pixel on the display.
*
* @param[in] x X location of the pixel
* @param[in] y Y location of the pixel
* @param[in] color The color of the pixel
*
* @notapi
*/
void gdisp_lld_draw_pixel(coord_t x, coord_t y, color_t color) {
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
if (x < GDISP.clipx0 || y < GDISP.clipy0 || x >= GDISP.clipx1 || y >= GDISP.clipy1) return;
#endif
acquire_bus();
set_cursor(x, y);
write_reg(0x0022, color);
release_bus();
}
/* ---- Optional Routines ---- */
/*
All the below routines are optional.
Defining them will increase speed but everything
will work if they are not defined.
If you are not using a routine - turn it off using
the appropriate GDISP_HARDWARE_XXXX macro.
Don't bother coding for obvious similar routines if
there is no performance penalty as the emulation software
makes a good job of using similar routines.
eg. If gfillarea() is defined there is little
point in defining clear() unless the
performance bonus is significant.
For good performance it is suggested to implement
fillarea() and blitarea().
*/
#if GDISP_HARDWARE_CLEARS || defined(__DOXYGEN__)
/**
* @brief Clear the display.
* @note Optional - The high level driver can emulate using software.
*
* @param[in] color The color of the pixel
*
* @notapi
*/
void gdisp_lld_clear(color_t color) {
unsigned area;
area = GDISP_SCREEN_WIDTH * GDISP_SCREEN_HEIGHT;
acquire_bus();
reset_viewport();
set_cursor(0, 0);
stream_start();
#if defined(GDISP_USE_FSMC) && defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
uint8_t i;
dmaStreamSetPeripheral(GDISP_DMA_STREAM, &color);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
for (i = area/65535; i; i--) {
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, 65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
}
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area%65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
#else
uint32_t index;
for(index = 0; index < area; index++)
write_data(color);
#endif //#ifdef GDISP_USE_DMA
stream_stop();
release_bus();
}
#endif
#if GDISP_HARDWARE_FILLS || defined(__DOXYGEN__)
/**
* @brief Fill an area with a color.
* @note Optional - The high level driver can emulate using software.
*
* @param[in] x, y The start filled area
* @param[in] cx, cy The width and height to be filled
* @param[in] color The color of the fill
*
* @notapi
*/
void gdisp_lld_fill_area(coord_t x, coord_t y, coord_t cx, coord_t cy, color_t color) {
unsigned area;
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
if (x < GDISP.clipx0) { cx -= GDISP.clipx0 - x; x = GDISP.clipx0; }
if (y < GDISP.clipy0) { cy -= GDISP.clipy0 - y; y = GDISP.clipy0; }
if (cx <= 0 || cy <= 0 || x >= GDISP.clipx1 || y >= GDISP.clipy1) return;
if (x+cx > GDISP.clipx1) cx = GDISP.clipx1 - x;
if (y+cy > GDISP.clipy1) cy = GDISP.clipy1 - y;
#endif
area = cx*cy;
acquire_bus();
set_viewport(x, y, cx, cy);
stream_start();
#if defined(GDISP_USE_FSMC) && defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
uint8_t i;
dmaStreamSetPeripheral(GDISP_DMA_STREAM, &color);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
for (i = area/65535; i; i--) {
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, 65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
}
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area%65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
#else
uint32_t index;
for(index = 0; index < area; index++)
write_data(color);
#endif //#ifdef GDISP_USE_DMA
stream_stop();
release_bus();
}
#endif
#if GDISP_HARDWARE_BITFILLS || defined(__DOXYGEN__)
/**
* @brief Fill an area with a bitmap.
* @note Optional - The high level driver can emulate using software.
*
* @param[in] x, y The start filled area
* @param[in] cx, cy The width and height to be filled
* @param[in] srcx, srcy The bitmap position to start the fill from
* @param[in] srccx The width of a line in the bitmap.
* @param[in] buffer The pixels to use to fill the area.
*
* @notapi
*/
void gdisp_lld_blit_area_ex(coord_t x, coord_t y, coord_t cx, coord_t cy, coord_t srcx, coord_t srcy, coord_t srccx, const pixel_t *buffer) {
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
if (x < GDISP.clipx0) { cx -= GDISP.clipx0 - x; srcx += GDISP.clipx0 - x; x = GDISP.clipx0; }
if (y < GDISP.clipy0) { cy -= GDISP.clipy0 - y; srcy += GDISP.clipy0 - y; y = GDISP.clipy0; }
if (srcx+cx > srccx) cx = srccx - srcx;
if (cx <= 0 || cy <= 0 || x >= GDISP.clipx1 || y >= GDISP.clipy1) return;
if (x+cx > GDISP.clipx1) cx = GDISP.clipx1 - x;
if (y+cy > GDISP.clipy1) cy = GDISP.clipy1 - y;
#endif
buffer += srcx + srcy * srccx;
acquire_bus();
set_viewport(x, y, cx, cy);
stream_start();
#if defined(GDISP_USE_FSMC) && defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
uint32_t area = cx*cy;
uint8_t i;
dmaStreamSetPeripheral(GDISP_DMA_STREAM, buffer);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PINC | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
for (i = area/65535; i; i--) {
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, 65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
}
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area%65535);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
#else
coord_t endx, endy;
uint32_t lg;
endx = srcx + cx;
endy = y + cy;
lg = srccx - cx;
for(; y < endy; y++, buffer += lg)
for(x=srcx; x < endx; x++)
write_data(*buffer++);
#endif //#ifdef GDISP_USE_DMA
stream_stop();
release_bus();
}
#endif
#if (GDISP_NEED_PIXELREAD && GDISP_HARDWARE_PIXELREAD) || defined(__DOXYGEN__)
/**
* @brief Get the color of a particular pixel.
* @note Optional.
* @note If x,y is off the screen, the result is undefined.
*
* @param[in] x, y The pixel to be read
*
* @notapi
*/
color_t gdisp_lld_get_pixel_color(coord_t x, coord_t y) {
color_t color;
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
if (x < 0 || x >= GDISP.Width || y < 0 || y >= GDISP.Height) return 0;
#endif
acquire_bus();
set_cursor(x, y);
stream_start();
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_Bank+1] = FSMC_BTR1_ADDSET_3 | FSMC_BTR1_DATAST_3 | FSMC_BTR1_BUSTURN_0 ;
color = read_data(); // dummy read
color = read_data();
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_Bank+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
stream_stop();
release_bus();
return color;
}
#endif
#if (GDISP_NEED_SCROLL && GDISP_HARDWARE_SCROLL) || defined(__DOXYGEN__)
/**
* @brief Scroll vertically a section of the screen.
* @note Optional.
* @note If x,y + cx,cy is off the screen, the result is undefined.
* @note If lines is >= cy, it is equivelent to a area fill with bgcolor.
*
* @param[in] x, y The start of the area to be scrolled
* @param[in] cx, cy The size of the area to be scrolled
* @param[in] lines The number of lines to scroll (Can be positive or negative)
* @param[in] bgcolor The color to fill the newly exposed area.
*
* @notapi
*/
void gdisp_lld_vertical_scroll(coord_t x, coord_t y, coord_t cx, coord_t cy, int lines, color_t bgcolor) {
static color_t buf[((GDISP_SCREEN_HEIGHT > GDISP_SCREEN_WIDTH ) ? GDISP_SCREEN_HEIGHT : GDISP_SCREEN_WIDTH)];
coord_t row0, row1;
unsigned i, gap, abslines, j;
#if GDISP_NEED_VALIDATION || GDISP_NEED_CLIP
if (x < GDISP.clipx0) { cx -= GDISP.clipx0 - x; x = GDISP.clipx0; }
if (y < GDISP.clipy0) { cy -= GDISP.clipy0 - y; y = GDISP.clipy0; }
if (!lines || cx <= 0 || cy <= 0 || x >= GDISP.clipx1 || y >= GDISP.clipy1) return;
if (x+cx > GDISP.clipx1) cx = GDISP.clipx1 - x;
if (y+cy > GDISP.clipy1) cy = GDISP.clipy1 - y;
#endif
abslines = lines < 0 ? -lines : lines;
acquire_bus();
if ((coord_t)abslines >= cy) {
abslines = cy;
gap = 0;
} else {
gap = cy - abslines;
for(i = 0; i < gap; i++) {
if(lines > 0) {
row0 = y + i + lines;
row1 = y + i;
} else {
row0 = (y - i - 1) + lines;
row1 = (y - i - 1);
}
/* read row0 into the buffer and then write at row1*/
set_viewport(x, row0, cx, 1);
stream_start();
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_Bank+1] = FSMC_BTR1_ADDSET_3 | FSMC_BTR1_DATAST_3 | FSMC_BTR1_BUSTURN_0 ;
j = read_data(); // dummy read
for (j = 0; (coord_t)j < cx; j++)
buf[j] = read_data();
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_Bank+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
stream_stop();
set_viewport(x, row1, cx, 1);
stream_start();
for (j = 0; (coord_t)j < cx; j++)
write_data(buf[j]);
stream_stop();
}
}
/* fill the remaining gap */
set_viewport(x, lines > 0 ? (y+(coord_t)gap) : y, cx, abslines);
stream_start();
gap = cx*abslines;
for(i = 0; i < gap; i++) write_data(bgcolor);
stream_stop();
release_bus();
}
#endif
#if (GDISP_NEED_CONTROL && GDISP_HARDWARE_CONTROL) || defined(__DOXYGEN__)
/**
* @brief Driver Control
* @details Unsupported control codes are ignored.
* @note The value parameter should always be typecast to (void *).
* @note There are some predefined and some specific to the low level driver.
* @note GDISP_CONTROL_POWER - Takes a gdisp_powermode_t
* GDISP_CONTROL_ORIENTATION - Takes a gdisp_orientation_t
* GDISP_CONTROL_BACKLIGHT - Takes an int from 0 to 100. For a driver
* that only supports off/on anything other
* than zero is on.
* GDISP_CONTROL_CONTRAST - Takes an int from 0 to 100.
* GDISP_CONTROL_LLD - Low level driver control constants start at
* this value.
*
* @param[in] what What to do.
* @param[in] value The value to use (always cast to a void *).
*
* @notapi
*/
void gdisp_lld_control(unsigned what, void *value) {
switch(what) {
case GDISP_CONTROL_POWER:
if (GDISP.Powermode == (gdisp_powermode_t)value)
return;
switch((gdisp_powermode_t)value) {
case powerOff:
acquire_bus();
write_reg(0x0010, 0x0000); // leave sleep mode
write_reg(0x0007, 0x0000); // halt operation
write_reg(0x0000, 0x0000); // turn off oszillator
write_reg(0x0010, 0x0001); // enter sleepmode
release_bus();
break;
case powerOn:
acquire_bus();
write_reg(0x0010, 0x0000); // leave sleep mode
release_bus();
if (GDISP.Powermode != powerSleep)
gdisp_lld_init();
break;
case powerSleep:
acquire_bus();
write_reg(0x0010, 0x0001); // enter sleep mode
release_bus();
break;
default:
return;
}
GDISP.Powermode = (gdisp_powermode_t)value;
return;
case GDISP_CONTROL_ORIENTATION:
if (GDISP.Orientation == (gdisp_orientation_t)value)
return;
switch((gdisp_orientation_t)value) {
case GDISP_ROTATE_0:
acquire_bus();
write_reg(0x0001, 0x2B3F);
/* ID = 11 AM = 0 */
write_reg(0x0011, 0x6070);
release_bus();
GDISP.Height = GDISP_SCREEN_HEIGHT;
GDISP.Width = GDISP_SCREEN_WIDTH;
break;
case GDISP_ROTATE_90:
acquire_bus();
write_reg(0x0001, 0x293F);
/* ID = 11 AM = 1 */
write_reg(0x0011, 0x6078);
release_bus();
GDISP.Height = GDISP_SCREEN_WIDTH;
GDISP.Width = GDISP_SCREEN_HEIGHT;
break;
case GDISP_ROTATE_180:
acquire_bus();
write_reg(0x0001, 0x2B3F);
/* ID = 01 AM = 0 */
write_reg(0x0011, 0x6040);
release_bus();
GDISP.Height = GDISP_SCREEN_HEIGHT;
GDISP.Width = GDISP_SCREEN_WIDTH;
break;
case GDISP_ROTATE_270:
acquire_bus();
write_reg(0x0001, 0x293F);
/* ID = 01 AM = 1 */
write_reg(0x0011, 0x6048);
release_bus();
GDISP.Height = GDISP_SCREEN_WIDTH;
GDISP.Width = GDISP_SCREEN_HEIGHT;
break;
default:
return;
}
#if GDISP_NEED_CLIP || GDISP_NEED_VALIDATION
GDISP.clipx0 = 0;
GDISP.clipy0 = 0;
GDISP.clipx1 = GDISP.Width;
GDISP.clipy1 = GDISP.Height;
#endif
GDISP.Orientation = (gdisp_orientation_t)value;
return;
case GDISP_CONTROL_BACKLIGHT:
if ((unsigned)value > 100)
value = (void *)100;
set_backlight((unsigned)value);
GDISP.Backlight = (unsigned)value;
return;
default:
return;
/*
case GDISP_CONTROL_CONTRAST:
*/
}
}
#endif
#endif /* GFX_USE_GDISP */
/** @} */
Reference in New Issue View Git Blame Copy Permalink