The offical µGFX repository.
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 

115 lines
3.1 KiB

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file boards/addons/gdisp/board_SSD1306_spi.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
*
* @note This file contains a mix of hardware specific and operating system specific
* code. You will need to change it for your CPU and/or operating system.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// Pin & SPI setup
#define SPI_DRIVER (&SPID2)
#define SPI_PORT GPIOB
#define SCK_PAD 13
#define MISO_PAD 14
#define MOSI_PAD 15
#define CS_PORT GPIOC
#define RESET_PORT GPIOC
#define DNC_PORT GPIOC
#define CS_PAD 7 // 0 = chip selected
#define RESET_PAD 8 // 0 = reset
#define DNC_PAD 9 // control=0, data=1
static SPIConfig spi_cfg = { NULL, CS_PORT, CS_PAD, 0 };
static GFXINLINE void init_board(GDisplay *g) {
(void) g;
g->board = 0;
// Maximum speed of SSD1306 is 10Mhz, so set SPI speed less or = to that.
//
// STM32 specific setup
// STM32_PCLK1 is APB1 frequence in hertz.
// STM32_PCLK2 is APB2 frequence in hertz.
// See manual clock diagram to determine APB1 or APB2 for spi in use.
// SPI2 uses APB1 clock on stm32151
// BR bits divide PCLK as follows
// 000 /2 = 16 MHz
// 001 /4 = 8 MHz
// 010 /8 = 4 MHz
// 011 /16 = 2 MHz
// 100 /32 = 1 MHz
// 101 /64 = 500 kHz
// 110 /128 = 250 kHz
// 111 /256 = 125 kHz
unsigned long spi_clk = STM32_PCLK1 / 2;
unsigned code = 0;
while (spi_clk > 10000000) {
code++;
spi_clk /= 2;
}
spi_cfg.cr1 |= (code << 3);
if (g->controllerdisplay == 0) {
palSetPadMode(SPI_PORT, SCK_PAD, PAL_MODE_ALTERNATE(5)|PAL_STM32_OTYPE_PUSHPULL|PAL_STM32_OSPEED_MID2);
palSetPadMode(SPI_PORT, MOSI_PAD, PAL_MODE_ALTERNATE(5)|PAL_STM32_OTYPE_PUSHPULL|PAL_STM32_OSPEED_MID2);
palSetPadMode(SPI_PORT, MISO_PAD, PAL_MODE_ALTERNATE(5));
palSetPadMode(RESET_PORT, RESET_PAD, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(CS_PORT, CS_PAD, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(DNC_PORT, DNC_PAD, PAL_MODE_OUTPUT_PUSHPULL);
palSetPad(CS_PORT, CS_PAD);
palSetPad(RESET_PORT, RESET_PAD);
palClearPad(DNC_PORT, DNC_PAD);
}
}
static GFXINLINE void post_init_board(GDisplay *g) {
(void) g;
}
static GFXINLINE void setpin_reset(GDisplay *g, bool_t state) {
(void) g;
palWritePad(RESET_PORT, RESET_PAD, !state);
}
static GFXINLINE void acquire_bus(GDisplay *g) {
(void) g;
spiAcquireBus(SPI_DRIVER);
spiStart(SPI_DRIVER, &spi_cfg);
spiSelect(SPI_DRIVER);
}
static GFXINLINE void release_bus(GDisplay *g) {
(void) g;
spiUnselect(SPI_DRIVER);
spiStop(SPI_DRIVER);
spiReleaseBus(SPI_DRIVER);
}
static GFXINLINE void write_cmd(GDisplay *g, uint8_t cmd) {
(void) g;
static uint8_t buf;
palClearPad(DNC_PORT, DNC_PAD);
buf = cmd;
spiSend(SPI_DRIVER, 1, &buf);
}
static GFXINLINE void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
(void) g;
palSetPad(DNC_PORT, DNC_PAD);
spiSend(SPI_DRIVER, length, data);
}
#endif /* _GDISP_LLD_BOARD_H */