114 lines
2.9 KiB
C
114 lines
2.9 KiB
C
/*
|
|
* This file is subject to the terms of the GFX License. If a copy of
|
|
* the license was not distributed with this file, you can obtain one at:
|
|
*
|
|
* http://ugfx.org/license.html
|
|
*/
|
|
|
|
/**
|
|
* @file drivers/gdisp/RA8875/board_RA8875_marlin.h
|
|
* @brief GDISP Graphic Driver subsystem board interface for the RA8875 display.
|
|
*/
|
|
|
|
#ifndef _BOARD_RA8875_H
|
|
#define _BOARD_RA8875_H
|
|
|
|
// For a multiple display configuration we would put all this in a structure and then
|
|
// set g->board to that structure.
|
|
#define GDISP_RAM (*((volatile uint16_t *) 0x68000000)) /* RS = 0 */
|
|
#define GDISP_REG (*((volatile uint16_t *) 0x68020000)) /* RS = 1 */
|
|
#define FSMC_BANK 4
|
|
|
|
|
|
static inline void init_board(GDisplay *g) {
|
|
// As we are not using multiple displays we set g->board to NULL as we don't use it.
|
|
g->board = 0;
|
|
|
|
switch(g->controllerdisplay) {
|
|
// setup for display 0
|
|
case 0: {
|
|
|
|
// enable the FSMC peripheral
|
|
rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
|
|
|
|
// setup the pin modes for FSMC
|
|
IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 8) |
|
|
(1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0};
|
|
|
|
IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
|
|
(1 << 13) | (1 << 14) | (1 << 15), 0};
|
|
|
|
IOBus busG = {GPIOG, (1 << 10), 0};
|
|
|
|
palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
|
|
palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
|
|
palSetBusMode(&busG, PAL_MODE_ALTERNATE(12));
|
|
|
|
// FSMC timing
|
|
FSMC_Bank1->BTCR[FSMC_BANK+1] = (FSMC_BTR1_ADDSET_1 | FSMC_BTR1_ADDSET_3) \
|
|
| (FSMC_BTR1_DATAST_1 | FSMC_BTR1_DATAST_3) \
|
|
| (FSMC_BTR1_BUSTURN_1 | FSMC_BTR1_BUSTURN_3) ;
|
|
|
|
// Bank1 NOR/SRAM control register configuration
|
|
// This is actually not needed as already set by default after reset
|
|
FSMC_Bank1->BTCR[FSMC_BANK] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
|
|
|
|
break;
|
|
}
|
|
|
|
// marlin does not have any secondary display so far
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static inline void post_init_board(GDisplay *g) {
|
|
(void) g;
|
|
|
|
// FSMC delay reduced as the controller now runs at full speed
|
|
FSMC_Bank1->BTCR[2+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
|
|
FSMC_Bank1->BTCR[2] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
|
|
}
|
|
|
|
static inline void setpin_reset(GDisplay *g, bool_t state) {
|
|
(void) g;
|
|
(void) state;
|
|
}
|
|
|
|
static inline void acquire_bus(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static inline void release_bus(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static inline void write_index(GDisplay *g, uint16_t index) {
|
|
(void) g;
|
|
|
|
GDISP_REG = index;
|
|
}
|
|
|
|
static inline void write_data(GDisplay *g, uint16_t data) {
|
|
(void) g;
|
|
|
|
GDISP_RAM = data;
|
|
}
|
|
|
|
static inline void setreadmode(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static inline void setwritemode(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static inline uint16_t read_data(GDisplay *g) {
|
|
(void) g;
|
|
|
|
return GDISP_RAM;
|
|
}
|
|
|
|
#endif /* _BOARD_RA8875_H */
|
|
|