193 lines
6.6 KiB
C
193 lines
6.6 KiB
C
/*
|
|
* This file is subject to the terms of the GFX License. If a copy of
|
|
* the license was not distributed with this file, you can obtain one at:
|
|
*
|
|
* http://ugfx.org/license.html
|
|
*/
|
|
|
|
/**
|
|
* @file boards/base/Olimex-SAM7EX256-GE8/board_Nokia6610GE8.h
|
|
* @brief GDISP Graphic Driver subsystem board interface for the Olimex SAM7-EX256 board.
|
|
*/
|
|
|
|
#ifndef _GDISP_LLD_BOARD_H
|
|
#define _GDISP_LLD_BOARD_H
|
|
|
|
/*
|
|
* Set various display properties. These properties mostly depend on the exact controller chip you get.
|
|
* The defaults should work for most controllers.
|
|
*/
|
|
//#define GDISP_GE8_BROKEN_CONTROLLER GFXOFF // Uncomment this out if you have a controller thats not window wrap broken.
|
|
//#define GDISP_SCREEN_HEIGHT 130 // The visible display height
|
|
//#define GDISP_SCREEN_WIDTH 130 // The visible display width
|
|
//#define GDISP_RAM_X_OFFSET 0 // The x offset of the visible area
|
|
//#define GDISP_RAM_Y_OFFSET 2 // The y offset of the visible area
|
|
//#define GDISP_SLEEP_SIZE 32 // The size of the sleep mode partial display
|
|
//#define GDISP_SLEEP_POS 50 // The position of the sleep mode partial display
|
|
//#define GDISP_INITIAL_CONTRAST 38 // The initial contrast percentage
|
|
//#define GDISP_INITIAL_BACKLIGHT 100 // The initial backlight percentage
|
|
|
|
// For a multiple display configuration we would put all this in a structure and then
|
|
// set g->board to that structure.
|
|
|
|
// ******************************************************
|
|
// Pointers to AT91SAM7X256 peripheral data structures
|
|
// ******************************************************
|
|
static volatile AT91PS_PIO pPIOA = AT91C_BASE_PIOA;
|
|
static volatile AT91PS_PIO pPIOB = AT91C_BASE_PIOB;
|
|
static volatile AT91PS_SPI pSPI = AT91C_BASE_SPI0;
|
|
static volatile AT91PS_PMC pPMC = AT91C_BASE_PMC;
|
|
|
|
/* The PWM backlight control is non-linear on this board.
|
|
* We pick values here that make it look a bit more linear.
|
|
*/
|
|
#define PWM_TOP_VALUE 500
|
|
#define PWM_BOTTOM_VALUE 200
|
|
|
|
#define PWM_VALUE(x) (PWM_BOTTOM_VALUE+(PWM_TOP_VALUE-PWM_BOTTOM_VALUE)*(x)/100)
|
|
|
|
/* PWM configuration structure. The LCD Backlight is on PWM1/PB20 ie PWM2/PIN1 in ChibiOS speak */
|
|
static const PWMConfig pwmcfg = {
|
|
1000000, /* 1 MHz PWM clock frequency. Ignored as we are using PWM_MCK_DIV_n */
|
|
1000, /* PWM period is 1000 cycles. */
|
|
0,
|
|
{
|
|
{PWM_MCK_DIV_1 | PWM_OUTPUT_ACTIVE_HIGH | PWM_OUTPUT_PIN1 | PWM_DISABLEPULLUP_PIN1, 0},
|
|
},
|
|
};
|
|
|
|
static gBool pwmRunning = gFalse;
|
|
|
|
/**
|
|
* @brief Initialise the board for the display.
|
|
* @notes Performs the following functions:
|
|
* 1. initialise the spi port used by your display
|
|
* 2. initialise the reset pin (initial state not-in-reset)
|
|
* 3. initialise the chip select pin (initial state not-active)
|
|
* 4. initialise the backlight pin (initial state back-light off)
|
|
*
|
|
* @notapi
|
|
*/
|
|
static GFXINLINE void init_board(GDisplay *g) {
|
|
|
|
// As we are not using multiple displays we set g->board to NULL as we don't use it.
|
|
g->board = 0;
|
|
|
|
switch(g->controllerdisplay) {
|
|
case 0: // Set up for Display 0
|
|
// *********************************************************************************************
|
|
// InitSpi( )
|
|
//
|
|
// Sets up SPI channel 0 for communications to Nokia 6610 LCD Display
|
|
//
|
|
// I/O ports used: PA2 = LCD Reset (set to low to reset)
|
|
// PA12 = LCD chip select (set to low to select the LCD chip)
|
|
// PA16 = SPI0_MISO Master In - Slave Out (not used in LCD interface)
|
|
// PA17 = SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave)
|
|
// PA18 = SPI0_SPCK Serial Clock (to LCD slave)
|
|
// PB20 = backlight control (normally PWM control, 1 = full on)
|
|
//
|
|
// *********************************************************************************************}
|
|
|
|
/* This code should really use the ChibiOS driver for these functions */
|
|
|
|
// Pin for backlight
|
|
pPIOB->PIO_CODR = PIOB_LCD_BL_MASK; // Set PB20 to LOW
|
|
pPIOB->PIO_OER = PIOB_LCD_BL_MASK; // Configure PB20 as output
|
|
|
|
// Reset pin
|
|
pPIOA->PIO_SODR = PIOA_LCD_RESET_MASK; // Set PA2 to HIGH
|
|
pPIOA->PIO_OER = PIOA_LCD_RESET_MASK; // Configure PA2 as output
|
|
|
|
// CS pin - this is driven automatically by the SPI hardware itself
|
|
|
|
// Init SPI0
|
|
// Disable the following pins from PIO control (will be used instead by the SPI0 peripheral)
|
|
// BIT12 = PA12 -> SPI0_NPCS0 chip select
|
|
// BIT16 = PA16 -> SPI0_MISO Master In - Slave Out (not used in LCD interface)
|
|
// BIT17 = PA17 -> SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave)
|
|
// BIT18 = PA18 -> SPI0_SPCK Serial Clock (to LCD slave)
|
|
pPIOA->PIO_PDR = (1<<12) | (1<<16) | (1<<17) | (1<<18);
|
|
pPIOA->PIO_ASR = (1<<12) | (1<<16) | (1<<17) | (1<<18);
|
|
|
|
//enable the clock of SPI
|
|
pPMC->PMC_PCER = 1 << AT91C_ID_SPI0;
|
|
|
|
// Fixed mode
|
|
pSPI->SPI_CR = 0x81; //SPI Enable, Software reset
|
|
pSPI->SPI_CR = 0x81; //SPI Enable, Software reset - 2nd write as per errata
|
|
pSPI->SPI_CR = 0x01; //SPI Enable
|
|
pSPI->SPI_MR = 0x000E0011; //Master mode, fixed select, disable decoder, PCS=1110
|
|
pSPI->SPI_CSR[0] = 0x00000311; //9bit, CPOL=1, ClockPhase=0, SCLK = 48Mhz/3 = 16MHz
|
|
|
|
/* Display backlight control at 100% */
|
|
pwmRunning = gFalse;
|
|
palSetPad(IOPORT2, PIOB_LCD_BL);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static GFXINLINE void post_init_board(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static GFXINLINE void setpin_reset(GDisplay *g, gBool state) {
|
|
(void) g;
|
|
if (state)
|
|
palClearPad(IOPORT1, PIOA_LCD_RESET);
|
|
else
|
|
palSetPad(IOPORT1, PIOA_LCD_RESET);
|
|
}
|
|
|
|
static GFXINLINE void set_backlight(GDisplay *g, uint8_t percent) {
|
|
(void) g;
|
|
if (percent == 100) {
|
|
/* Turn the pin on - No PWM */
|
|
if (pwmRunning) {
|
|
pwmStop(&PWMD2);
|
|
pwmRunning = gFalse;
|
|
}
|
|
palSetPad(IOPORT2, PIOB_LCD_BL);
|
|
} else if (percent == 0) {
|
|
/* Turn the pin off - No PWM */
|
|
if (pwmRunning) {
|
|
pwmStop(&PWMD2);
|
|
pwmRunning = gFalse;
|
|
}
|
|
palClearPad(IOPORT2, PIOB_LCD_BL);
|
|
} else {
|
|
/* Use the PWM */
|
|
if (!pwmRunning) {
|
|
pwmStart(&PWMD2, &pwmcfg);
|
|
pwmRunning = gTrue;
|
|
}
|
|
pwmEnableChannel(&PWMD2, 0, PWM_VALUE(percent));
|
|
}
|
|
}
|
|
|
|
static GFXINLINE void acquire_bus(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static GFXINLINE void release_bus(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
static GFXINLINE void write_index(GDisplay *g, uint16_t index) {
|
|
(void) g;
|
|
// wait for the previous transfer to start
|
|
while(!(pSPI->SPI_SR & AT91C_SPI_TDRE));
|
|
// send the command
|
|
pSPI->SPI_TDR = index & 0xFF;
|
|
}
|
|
|
|
static GFXINLINE void write_data(GDisplay *g, uint16_t data) {
|
|
(void) g;
|
|
// wait for the previous transfer to start
|
|
while(!(pSPI->SPI_SR & AT91C_SPI_TDRE));
|
|
// send the data
|
|
pSPI->SPI_TDR = data | 0x0100;
|
|
}
|
|
|
|
#endif /* _GDISP_LLD_BOARD_H */
|