89 lines
2.1 KiB
C++
89 lines
2.1 KiB
C++
#include <Arduino.h>
|
|
#include <SPI.h>
|
|
#include <Wire.h>
|
|
|
|
#include "board_SSD1331.h"
|
|
|
|
#define LCD_BOARD_ID 0 // 0 or 1 - set by the position of a resistor near SX1505 (see schematic and board design)
|
|
|
|
// GPIO Pins
|
|
#define GPIO_DC 0x01
|
|
#define GPIO_CS 0x02
|
|
#define GPIO_RES 0x08
|
|
#define GPIO_BTN1 0x10
|
|
#define GPIO_BTN2 0x20
|
|
#define GPIO_BTN3 0x40
|
|
#define GPIO_BTN4 0x80
|
|
#define GPIO_CMD_START ~(GPIO_CS|GPIO_DC)
|
|
#define GPIO_DATA_START ~GPIO_CS
|
|
#define GPIO_TRANSFER_END GPIO_CS
|
|
|
|
//GPIO Registers
|
|
#define GPIO_RegData 0x00
|
|
#define GPIO_RegDir 0x01
|
|
#define GPIO_RegPullUp 0x02
|
|
|
|
// Wire address of the SX1505 chip
|
|
#define GPIO_ADDR 0x20
|
|
|
|
static void writeGPIO(uint8_t regAddr, uint8_t regData)
|
|
{
|
|
uint8_t oldTWBR=TWBR;
|
|
TWBR=0;
|
|
Wire.beginTransmission(GPIO_ADDR + LCD_BOARD_ID);
|
|
Wire.write(regAddr);
|
|
Wire.write(regData);
|
|
Wire.endTransmission();
|
|
TWBR=oldTWBR;
|
|
}
|
|
|
|
static bool isDataMode = false;
|
|
static bool isCmdMode = false;
|
|
|
|
void SSD1331_init_board(void) {
|
|
//setup GPIO, reset SSD1331
|
|
writeGPIO(GPIO_RegData,~GPIO_RES);//reset low, CS/other pins high
|
|
writeGPIO(GPIO_RegDir,~GPIO_RES);//set reset to output
|
|
delay(5);
|
|
writeGPIO(GPIO_RegDir,~(GPIO_CS|GPIO_DC));//reset to input, CS/DC output
|
|
writeGPIO(GPIO_RegPullUp,GPIO_BTN1|GPIO_BTN2|GPIO_BTN3|GPIO_BTN4);//button pullup enable
|
|
//init SPI
|
|
SPI.begin();
|
|
SPI.setDataMode(SPI_MODE0);//wrong mode, works because we're only writing. this mode is compatible with SD cards.
|
|
SPI.setClockDivider(SPI_CLOCK_DIV2);
|
|
|
|
isDataMode = isCmdMode = false;
|
|
}
|
|
|
|
void SSD1331_setpin_reset(int state) {
|
|
// Ignore this as we did it in the init_board
|
|
}
|
|
|
|
void SSD1331_aquirebus(void) {
|
|
// Do nothing as we do it in the data transfer
|
|
}
|
|
|
|
void SSD1331_releasebus(void) {
|
|
if (!isDataMode && !isCmdMode) return;
|
|
writeGPIO(GPIO_RegData,GPIO_TRANSFER_END);
|
|
isDataMode = isCmdMode = false;
|
|
}
|
|
|
|
void SSD1331_write_cmd(uint8_t cmd) {
|
|
if (!isCmdMode) {
|
|
writeGPIO(GPIO_RegData,GPIO_CMD_START);
|
|
isDataMode = false;
|
|
isCmdMode = true;
|
|
}
|
|
SPI.transfer(cmd);
|
|
}
|
|
|
|
void SSD1331_write_data(uint8_t data) {
|
|
if (!isDataMode) {
|
|
writeGPIO(GPIO_RegData,GPIO_DATA_START);
|
|
isDataMode = true;
|
|
isCmdMode = false;
|
|
}
|
|
SPI.transfer(data);
|
|
}
|