397 lines
14 KiB
C
397 lines
14 KiB
C
/*
|
|
* This file is subject to the terms of the GFX License. If a copy of
|
|
* the license was not distributed with this file, you can obtain one at:
|
|
*
|
|
* http://ugfx.org/license.html
|
|
*/
|
|
|
|
#include "gfx.h"
|
|
|
|
#if GFX_USE_GDISP
|
|
|
|
#define GDISP_DRIVER_VMT GDISPVMT_SSD1963
|
|
#include "gdisp_lld_config.h"
|
|
#include "../../../src/gdisp/gdisp_driver.h"
|
|
|
|
#define CALC_PERIOD(w,b,f,p) (p+b+w+f)
|
|
#define CALC_FPR(w,h,hb,hf,hp,vb,vf,vp,fps) ((fps * CALC_PERIOD(w,hb,hf,hp) * CALC_PERIOD(h,vb,vf,vp) * 1048576)/100000000)
|
|
|
|
typedef struct LCD_Parameters {
|
|
gCoord width, height; // Panel width and height
|
|
uint16_t hbporch; // Horizontal Back Porch
|
|
uint16_t hfporch; // Horizontal Front Porch
|
|
uint16_t hpulse; // Horizontal Pulse
|
|
uint16_t hperiod; // Horizontal Period (Total)
|
|
uint16_t vbporch; // Vertical Back Porch
|
|
uint16_t vfporch; // Vertical Front Porch
|
|
uint16_t vpulse; // Vertical Pulse
|
|
uint16_t vperiod; // Vertical Period (Total)
|
|
uint32_t fpr; // Calculated FPR
|
|
uint16_t mode; // For command "SSD1963_SET_LCD_MODE"
|
|
/* Set the pannel data width */
|
|
#define LCD_PANEL_DATA_WIDTH_24BIT (1<<5) // 18bit default
|
|
/* Set the color deeph enhancement */
|
|
#define LCD_PANEL_ENABLE_FRC ((1<<3) | (1<<4))
|
|
#define LCD_PANEL_ENABLE_DITHERING (1<<4) // no enhancement default
|
|
/* Set the dot clock pulse polarity */
|
|
#define LCD_PANEL_LSHIFT_FALLING_EDGE (1<<2) // default rising edge
|
|
/* Set the horizontal sync pulse polarity */
|
|
#define LCD_PANEL_LLINE_ACTIVE_HIGH (1<<1) // default active low
|
|
/* Set the vertical sync pulse polarity */
|
|
#define LCD_PANEL_LFRAME_ACTIVE_HIGH (1<0) // default active low
|
|
/* Set the lcd panel mode */
|
|
#define LCD_PANEL_MODE_TTL ((1<<7) << 8) // default mode is Hsync+Vsync +DE
|
|
/* Set the lcd panel interface type */ // default TFT mode
|
|
#define LCD_PANEL_TYPE_SERIAL_RGB_MODE ((1<<6) << 8) // Serial RGB mode
|
|
#define LCD_PANEL_TYPE_SERIAL_RGB_DUMMY_MODE (((1<<5) | (1<<6)) << 8) // Serial RGB+dummy mode
|
|
|
|
gBool flipHorz; // Flipping the display horizontally
|
|
gBool flipVert; // Flipping the display vertically
|
|
} LCD_Parameters;
|
|
|
|
#include "board_SSD1963.h"
|
|
|
|
/*===========================================================================*/
|
|
/* Driver local definitions. */
|
|
/*===========================================================================*/
|
|
|
|
#ifndef GDISP_SSD1963_NO_INIT
|
|
#define GDISP_SSD1963_NO_INIT GFXOFF
|
|
#endif
|
|
#ifndef GDISP_INITIAL_CONTRAST
|
|
#define GDISP_INITIAL_CONTRAST 50
|
|
#endif
|
|
#ifndef GDISP_INITIAL_BACKLIGHT
|
|
#define GDISP_INITIAL_BACKLIGHT 100
|
|
#endif
|
|
|
|
/*===========================================================================*/
|
|
/* Driver local functions. */
|
|
/*===========================================================================*/
|
|
|
|
#include "ssd1963.h"
|
|
|
|
#define dummy_read(g) { volatile uint16_t dummy; dummy = read_data(g); (void) dummy; }
|
|
#define write_reg(g, reg, data) { write_index(g, reg); write_data(g, data); }
|
|
#define write_data16(g, data) { write_data(g, (data)>>8); write_data(g, (data) & 0xFF); }
|
|
#define read_reg(g, reg) { write_index(g, reg); read_data(g); }
|
|
|
|
static GFXINLINE void set_viewport(GDisplay* g) {
|
|
switch(g->g.Orientation) {
|
|
default:
|
|
case GDISP_ROTATE_0:
|
|
write_index(g, SSD1963_SET_COLUMN_ADDRESS);
|
|
write_data16(g, g->p.x);
|
|
write_data16(g, g->p.x+g->p.cx-1);
|
|
write_index(g, SSD1963_SET_PAGE_ADDRESS);
|
|
write_data16(g, g->p.y);
|
|
write_data16(g, g->p.y+g->p.cy-1);
|
|
write_index(g, SSD1963_WRITE_MEMORY_START);
|
|
break;
|
|
case GDISP_ROTATE_90:
|
|
write_index(g, SSD1963_SET_COLUMN_ADDRESS);
|
|
write_data16(g, g->p.y);
|
|
write_data16(g, g->p.y+g->p.cy-1);
|
|
write_index(g, SSD1963_SET_PAGE_ADDRESS);
|
|
write_data16(g, g->g.Width - g->p.x - g->p.cx);
|
|
write_data16(g, g->g.Width-1 - g->p.x);
|
|
write_index(g, SSD1963_WRITE_MEMORY_START);
|
|
break;
|
|
case GDISP_ROTATE_180:
|
|
write_index(g, SSD1963_SET_COLUMN_ADDRESS);
|
|
write_data16(g, g->g.Width - g->p.x - g->p.cx);
|
|
write_data16(g, g->g.Width-1 - g->p.x);
|
|
write_index(g, SSD1963_SET_PAGE_ADDRESS);
|
|
write_data16(g, g->g.Height - g->p.y - g->p.cy);
|
|
write_data16(g, g->g.Height-1 - g->p.y);
|
|
write_index(g, SSD1963_WRITE_MEMORY_START);
|
|
break;
|
|
case GDISP_ROTATE_270:
|
|
write_index(g, SSD1963_SET_COLUMN_ADDRESS);
|
|
write_data16(g, g->g.Height - g->p.y - g->p.cy);
|
|
write_data16(g, g->g.Height-1 - g->p.y);
|
|
write_index(g, SSD1963_SET_PAGE_ADDRESS);
|
|
write_data16(g, g->p.x);
|
|
write_data16(g, g->p.x+g->p.cx-1);
|
|
write_index(g, SSD1963_WRITE_MEMORY_START);
|
|
break;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* The backlight is controlled by the controller.
|
|
* percent - the value 0..100 for brightness (duty cycle)
|
|
*
|
|
* Backlight appears to be forced off (by chip) when display blanked
|
|
*/
|
|
static GFXINLINE void set_backlight(GDisplay *g, uint8_t percent) {
|
|
// The SSD1963 has a built-in PWM (duty_cycle 00..FF).
|
|
// Its output can be used by a Dynamic Background Control or by a host (user)
|
|
// Check your LCD's hardware, the PWM connection is default left open and instead
|
|
// connected to a LED connection on the breakout board
|
|
|
|
write_index(g, SSD1963_SET_PWM_CONF); //set PWM for BackLight
|
|
write_data(g, 0x06);
|
|
// write_data(g, 0x0E); // PWMF[7:0] = 2, PWM base freq = PLL/(256*(1+5))/256 = 300Hz for a PLL freq = 120MHz (source: Displaytech)
|
|
if (percent == 0xFF) // use percent==0xFF to turn off SSD1963 pwm in power SLEEP or DEEP SLEEP mode
|
|
write_data(g, 0x00);
|
|
else if (percent >= 100)
|
|
write_data(g, 0xFF); // Fully on for any percentage >= 100
|
|
else
|
|
write_data(g, (percent*255)/100 & 0x00FF);
|
|
write_data(g, 0x01); // Controlled by host (not DBC), enabled
|
|
write_data(g, 0xFF); // DBC manual brightness (not used - zero would work)
|
|
write_data(g, 0x00); // DBC minimum brightness
|
|
write_data(g, 0x01); // Brightness prescaler - active when Transition Effect enable A5 = 1
|
|
}
|
|
|
|
/*===========================================================================*/
|
|
/* Driver exported functions. */
|
|
/*===========================================================================*/
|
|
|
|
LLDSPEC gBool gdisp_lld_init(GDisplay *g) {
|
|
LCD_Parameters * lcdp;
|
|
|
|
/*
|
|
* Some displays (e.g. Displaytech) have an on-board setup process which just requires that we don't touch anything for a time after power up.
|
|
* For this type of display define GDISP_SSD1963_NO_INIT as GFXON, and implement an appropriate delay in the board file.
|
|
* With such displays we can skip most of the initialisation. We also skip pulsing the reset pin, since it
|
|
* will introduce an extra second or so of display to the startup time.
|
|
*/
|
|
|
|
// The private area for this controller is the LCD timings
|
|
lcdp = (void *)&DisplayTimings[g->controllerdisplay];
|
|
g->priv = lcdp;
|
|
|
|
// Initialise the board interface
|
|
init_board(g);
|
|
|
|
#if !GDISP_SSD1963_NO_INIT
|
|
// Hardware reset
|
|
setpin_reset(g, gTrue);
|
|
gfxSleepMilliseconds(200);
|
|
setpin_reset(g, gFalse);
|
|
gfxSleepMilliseconds(200);
|
|
#endif
|
|
|
|
// Get the bus for the following initialisation commands
|
|
acquire_bus(g);
|
|
|
|
#if !GDISP_SSD1963_NO_INIT
|
|
write_index(g, SSD1963_SOFT_RESET); // Software reset - clears almost everything (apart from PLL)
|
|
write_index(g, SSD1963_SOFT_RESET); // Software reset - clears almost everything (apart from PLL)
|
|
write_index(g, SSD1963_SOFT_RESET); // Software reset - clears almost everything (apart from PLL)
|
|
gfxSleepMilliseconds(50);
|
|
|
|
/* Driver PLL config */
|
|
write_index(g, SSD1963_SET_PLL_MN);
|
|
write_data(g, 35); // PLLclk = REFclk (10Mhz) * 36 (360Mhz)
|
|
write_data(g, 2); // SYSclk = PLLclk / 3 (120MHz)
|
|
write_data(g, 54); // Apply calculation bit, else it is ignored
|
|
write_reg(g, SSD1963_SET_PLL, 0x01); // Enable PLL
|
|
gfxSleepMilliseconds(100);
|
|
write_reg(g, SSD1963_SET_PLL, 0x03); // Use PLL
|
|
|
|
/* LCD panel parameters */
|
|
write_index(g, SSD1963_SET_LCD_MODE);
|
|
write_data(g, lcdp->mode & 0xFF);
|
|
write_data(g, (lcdp->mode >> 8) & 0xFF);
|
|
//** write_data(g, 0x18); //Enabled dithering
|
|
//** write_data(g, 0x00);
|
|
write_data16(g, lcdp->width-1);
|
|
write_data16(g, lcdp->height-1);
|
|
write_data(g, 0x00); // RGB - line sequences for serial TFT
|
|
#endif
|
|
|
|
|
|
// Display flipping
|
|
if (lcdp->flipHorz) {
|
|
write_reg(g, SSD1963_SET_ADDRESS_MODE, SSD1963_ADDR_MODE_FLIP_HORZ);
|
|
} else if (lcdp->flipVert) {
|
|
write_reg(g, SSD1963_SET_ADDRESS_MODE, SSD1963_ADDR_MODE_FLIP_VERT);
|
|
} else if (lcdp->flipHorz && lcdp->flipVert) {
|
|
write_reg(g, SSD1963_SET_ADDRESS_MODE, SSD1963_ADDR_MODE_FLIP_VERT | SSD1963_ADDR_MODE_FLIP_HORZ);
|
|
} else {
|
|
write_reg(g, SSD1963_SET_ADDRESS_MODE, 0x00);
|
|
}
|
|
|
|
write_reg(g, SSD1963_SET_PIXEL_DATA_INTERFACE, SSD1963_PDI_16BIT565);
|
|
write_reg(g, SSD1963_SET_PIXEL_FORMAT, 0x50);
|
|
|
|
#if !GDISP_SSD1963_NO_INIT
|
|
/* LCD Clock specs */
|
|
write_index(g, SSD1963_SET_LSHIFT_FREQ);
|
|
write_data(g, (lcdp->fpr >> 16) & 0xFF);
|
|
write_data(g, (lcdp->fpr >> 8) & 0xFF);
|
|
write_data(g, lcdp->fpr & 0xFF);
|
|
|
|
write_index(g, SSD1963_SET_HORI_PERIOD);
|
|
write_data16(g, lcdp->hperiod);
|
|
write_data16(g, lcdp->hpulse + lcdp->hbporch);
|
|
write_data(g, lcdp->hpulse - 1);
|
|
write_data(g, 0x00);
|
|
write_data(g, 0x00);
|
|
write_data(g, 0x00);
|
|
|
|
write_index(g, SSD1963_SET_VERT_PERIOD);
|
|
write_data16(g, lcdp->vperiod);
|
|
write_data16(g, lcdp->vpulse + lcdp->vbporch);
|
|
write_data(g, lcdp->vpulse - 1);
|
|
write_data(g, 0x00);
|
|
write_data(g, 0x00);
|
|
|
|
#if 0
|
|
/* Enable DBC to control Backlight */
|
|
write_index(g, SSD1963_SET_DBC_CONF);
|
|
write_data(g, 0x2F);
|
|
#endif
|
|
#endif
|
|
|
|
#if 0
|
|
/* Tear effect indicator ON. This is used to tell the host MCU when the driver is not refreshing the panel (during front/back porch) */
|
|
write_reg(g, SSD1963_SET_TEAR_ON, 0x00);
|
|
#endif
|
|
|
|
/* Turn on */
|
|
write_index(g, SSD1963_SET_DISPLAY_ON);
|
|
|
|
/* Turn on the back-light */
|
|
set_backlight(g, GDISP_INITIAL_BACKLIGHT);
|
|
|
|
// Finish Init
|
|
post_init_board(g);
|
|
|
|
// Release the bus
|
|
release_bus(g);
|
|
|
|
/* Initialise the GDISP structure */
|
|
g->g.Width = lcdp->width;
|
|
g->g.Height = lcdp->height;
|
|
g->g.Orientation = GDISP_ROTATE_0;
|
|
g->g.Powermode = powerOn;
|
|
g->g.Backlight = GDISP_INITIAL_BACKLIGHT;
|
|
g->g.Contrast = GDISP_INITIAL_CONTRAST;
|
|
return gTrue;
|
|
}
|
|
|
|
#if GDISP_HARDWARE_STREAM_WRITE
|
|
LLDSPEC void gdisp_lld_write_start(GDisplay *g) {
|
|
acquire_bus(g);
|
|
set_viewport(g);
|
|
}
|
|
LLDSPEC void gdisp_lld_write_color(GDisplay *g) {
|
|
write_data(g, gdispColor2Native(g->p.color));
|
|
}
|
|
LLDSPEC void gdisp_lld_write_stop(GDisplay *g) {
|
|
release_bus(g);
|
|
}
|
|
#endif
|
|
|
|
#if GDISP_NEED_CONTROL && GDISP_HARDWARE_CONTROL
|
|
LLDSPEC void gdisp_lld_control(GDisplay *g) {
|
|
switch(g->p.x) {
|
|
case GDISP_CONTROL_POWER:
|
|
if (g->g.Powermode == (powermode_t)g->p.ptr)
|
|
return;
|
|
switch((powermode_t)g->p.ptr) {
|
|
case powerOff:
|
|
acquire_bus(g);
|
|
write_index(g, SSD1963_EXIT_SLEEP_MODE);
|
|
gfxSleepMilliseconds(5);
|
|
write_index(g, SSD1963_SET_DISPLAY_OFF);
|
|
write_index(g, SSD1963_SET_DEEP_SLEEP);
|
|
release_bus(g);
|
|
break;
|
|
case powerOn:
|
|
acquire_bus(g);
|
|
setreadmode(g);
|
|
dummy_read(g);
|
|
dummy_read(g);
|
|
setwritemode(g);
|
|
|
|
gfxSleepMilliseconds(100); // Wait for 1msec to let the PLL stable if was stopped by deep sleep mode
|
|
write_index(g, SSD1963_EXIT_SLEEP_MODE); // need this in case we were in 'normal' sleep mode
|
|
gfxSleepMilliseconds(5);
|
|
set_backlight(g, gdispGGetBacklight(g)); // Restore the back-light
|
|
release_bus(g);
|
|
break;
|
|
case powerSleep:
|
|
acquire_bus(g);
|
|
set_backlight(g, 0xFF); // Turn off the back-light pwm from SSD1963
|
|
write_index(g, SSD1963_ENTER_SLEEP_MODE);
|
|
gfxSleepMilliseconds(5);
|
|
release_bus(g);
|
|
break;
|
|
case powerDeepSleep:
|
|
acquire_bus(g);
|
|
set_backlight(g, 0xFF); // Turn off the back-light pwm from SSD1963
|
|
write_index(g, SSD1963_ENTER_SLEEP_MODE);
|
|
write_index(g, SSD1963_SET_DEEP_SLEEP);
|
|
release_bus(g);
|
|
break;
|
|
default:
|
|
return;
|
|
}
|
|
g->g.Powermode = (powermode_t)g->p.ptr;
|
|
return;
|
|
|
|
case GDISP_CONTROL_ORIENTATION:
|
|
if (g->g.Orientation == (orientation_t)g->p.ptr)
|
|
return;
|
|
switch((orientation_t)g->p.ptr) {
|
|
case GDISP_ROTATE_0:
|
|
acquire_bus(g);
|
|
write_index(g, SSD1963_SET_ADDRESS_MODE);
|
|
write_data(g, 0x00);
|
|
release_bus(g);
|
|
g->g.Height = ((LCD_Parameters *)g->priv)->height;
|
|
g->g.Width = ((LCD_Parameters *)g->priv)->width;
|
|
break;
|
|
case GDISP_ROTATE_90:
|
|
acquire_bus(g);
|
|
write_index(g, SSD1963_SET_ADDRESS_MODE);
|
|
write_data(g, SSD1963_ADDR_MODE_PAGE_ADDR_ORDER | SSD1963_ADDR_MODE_PAG_COL_ADDR_ORDER );
|
|
release_bus(g);
|
|
g->g.Height = ((LCD_Parameters *)g->priv)->width;
|
|
g->g.Width = ((LCD_Parameters *)g->priv)->height;
|
|
break;
|
|
case GDISP_ROTATE_180:
|
|
acquire_bus(g);
|
|
write_index(g, SSD1963_SET_ADDRESS_MODE);
|
|
write_data(g, SSD1963_ADDR_MODE_PAGE_ADDR_ORDER | SSD1963_ADDR_MODE_COL_ADDR_ORDER);
|
|
release_bus(g);
|
|
g->g.Height = ((LCD_Parameters *)g->priv)->height;
|
|
g->g.Width = ((LCD_Parameters *)g->priv)->width;
|
|
break;
|
|
case GDISP_ROTATE_270:
|
|
acquire_bus(g);
|
|
write_index(g, SSD1963_SET_ADDRESS_MODE);
|
|
write_data(g, SSD1963_ADDR_MODE_COL_ADDR_ORDER | SSD1963_ADDR_MODE_PAG_COL_ADDR_ORDER );
|
|
release_bus(g);
|
|
g->g.Height = ((LCD_Parameters *)g->priv)->width;
|
|
g->g.Width = ((LCD_Parameters *)g->priv)->height;
|
|
break;
|
|
default:
|
|
return;
|
|
}
|
|
g->g.Orientation = (orientation_t)g->p.ptr;
|
|
return;
|
|
|
|
case GDISP_CONTROL_BACKLIGHT:
|
|
if ((unsigned)g->p.ptr > 100)
|
|
g->p.ptr = (void *)100;
|
|
acquire_bus(g);
|
|
set_backlight(g, (unsigned)g->p.ptr);
|
|
release_bus(g);
|
|
g->g.Backlight = (unsigned)g->p.ptr;
|
|
return;
|
|
|
|
//case GDISP_CONTROL_CONTRAST: - see DDS1963_SET_POST_PROC command - contrast, brightness, saturation
|
|
default:
|
|
return;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#endif /* GFX_USE_GDISP */
|