17b921204c
Revert chibios 3.x use of bool as a base type for bool_t. back to char bool is available on c++ compilers only!!!!
116 lines
3.1 KiB
C
116 lines
3.1 KiB
C
/*
|
|
* This file is subject to the terms of the GFX License. If a copy of
|
|
* the license was not distributed with this file, you can obtain one at:
|
|
*
|
|
* http://ugfx.org/license.html
|
|
*/
|
|
|
|
/**
|
|
* @file boards/addons/gdisp/board_SSD1306_spi.h
|
|
* @brief GDISP Graphic Driver subsystem board interface for the SSD1306 display.
|
|
*
|
|
* @note This file contains a mix of hardware specific and operating system specific
|
|
* code. You will need to change it for your CPU and/or operating system.
|
|
*/
|
|
|
|
#ifndef _GDISP_LLD_BOARD_H
|
|
#define _GDISP_LLD_BOARD_H
|
|
|
|
// Pin & SPI setup
|
|
|
|
#define SPI_DRIVER (&SPID2)
|
|
#define SPI_PORT GPIOB
|
|
#define SCK_PAD 13
|
|
#define MISO_PAD 14
|
|
#define MOSI_PAD 15
|
|
|
|
#define CS_PORT GPIOC
|
|
#define RESET_PORT GPIOC
|
|
#define DNC_PORT GPIOC
|
|
#define CS_PAD 7 // 0 = chip selected
|
|
#define RESET_PAD 8 // 0 = reset
|
|
#define DNC_PAD 9 // control=0, data=1
|
|
|
|
static SPIConfig spi_cfg = { NULL, CS_PORT, CS_PAD, 0 };
|
|
|
|
static inline void init_board(GDisplay *g) {
|
|
(void) g;
|
|
g->board = 0;
|
|
// Maximum speed of SSD1306 is 10Mhz, so set SPI speed less or = to that.
|
|
//
|
|
// STM32 specific setup
|
|
// STM32_PCLK1 is APB1 frequence in hertz.
|
|
// STM32_PCLK2 is APB2 frequence in hertz.
|
|
// See manual clock diagram to determine APB1 or APB2 for spi in use.
|
|
// SPI2 uses APB1 clock on stm32151
|
|
// BR bits divide PCLK as follows
|
|
// 000 /2 = 16 MHz
|
|
// 001 /4 = 8 MHz
|
|
// 010 /8 = 4 MHz
|
|
// 011 /16 = 2 MHz
|
|
// 100 /32 = 1 MHz
|
|
// 101 /64 = 500 kHz
|
|
// 110 /128 = 250 kHz
|
|
// 111 /256 = 125 kHz
|
|
unsigned long spi_clk = STM32_PCLK1 / 2;
|
|
unsigned code = 0;
|
|
while (spi_clk > 10000000) {
|
|
code++;
|
|
spi_clk /= 2;
|
|
}
|
|
spi_cfg.cr1 |= (code << 3);
|
|
|
|
if (g->controllerdisplay == 0) {
|
|
palSetPadMode(SPI_PORT, SCK_PAD, PAL_MODE_ALTERNATE(5)|PAL_STM32_OTYPE_PUSHPULL|PAL_STM32_OSPEED_MID2);
|
|
palSetPadMode(SPI_PORT, MOSI_PAD, PAL_MODE_ALTERNATE(5)|PAL_STM32_OTYPE_PUSHPULL|PAL_STM32_OSPEED_MID2);
|
|
palSetPadMode(SPI_PORT, MISO_PAD, PAL_MODE_ALTERNATE(5));
|
|
palSetPadMode(RESET_PORT, RESET_PAD, PAL_MODE_OUTPUT_PUSHPULL);
|
|
palSetPadMode(CS_PORT, CS_PAD, PAL_MODE_OUTPUT_PUSHPULL);
|
|
palSetPadMode(DNC_PORT, DNC_PAD, PAL_MODE_OUTPUT_PUSHPULL);
|
|
palSetPad(CS_PORT, CS_PAD);
|
|
palSetPad(RESET_PORT, RESET_PAD);
|
|
palClearPad(DNC_PORT, DNC_PAD);
|
|
}
|
|
}
|
|
|
|
static inline void post_init_board(GDisplay *g) {
|
|
(void) g;
|
|
}
|
|
|
|
|
|
static inline void setpin_reset(GDisplay *g, bool_t state) {
|
|
(void) g;
|
|
palWritePad(RESET_PORT, RESET_PAD, !state);
|
|
}
|
|
|
|
static inline void acquire_bus(GDisplay *g) {
|
|
(void) g;
|
|
spiAcquireBus(SPI_DRIVER);
|
|
spiStart(SPI_DRIVER, &spi_cfg);
|
|
spiSelect(SPI_DRIVER);
|
|
}
|
|
|
|
static inline void release_bus(GDisplay *g) {
|
|
(void) g;
|
|
spiUnselect(SPI_DRIVER);
|
|
spiStop(SPI_DRIVER);
|
|
spiReleaseBus(SPI_DRIVER);
|
|
}
|
|
|
|
static inline void write_cmd(GDisplay *g, uint8_t cmd) {
|
|
(void) g;
|
|
static uint8_t buf;
|
|
palClearPad(DNC_PORT, DNC_PAD);
|
|
buf = cmd;
|
|
spiSend(SPI_DRIVER, 1, &buf);
|
|
}
|
|
|
|
static inline void write_data(GDisplay *g, uint8_t* data, uint16_t length) {
|
|
(void) g;
|
|
palSetPad(DNC_PORT, DNC_PAD);
|
|
spiSend(SPI_DRIVER, length, data);
|
|
}
|
|
|
|
|
|
#endif /* _GDISP_LLD_BOARD_H */
|