ugfx/drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h
2013-06-15 21:37:22 +10:00

146 lines
3.2 KiB
C

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://chibios-gfx.com/license.html
*/
/**
* @file drivers/gdisp/ILI9481/gdisp_lld_board_firebullstm32f103.h
* @brief GDISP Graphics Driver subsystem low level driver source for
* the ILI9481 and compatible HVGA display
*
* @addtogroup GDISP
* @{
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
#define SET_CS palSetPad(GPIOD, 12);
#define CLR_CS palClearPad(GPIOD, 12);
#define SET_RS palSetPad(GPIOD, 13);
#define CLR_RS palClearPad(GPIOD, 13);
#define SET_WR palSetPad(GPIOD, 14);
#define CLR_WR palClearPad(GPIOD, 14);
#define SET_RD palSetPad(GPIOD, 15);
#define CLR_RD palClearPad(GPIOD, 15);
/**
* @brief Initialise the board for the display.
* @notes This board definition uses GPIO and assumes exclusive access to these GPIO pins
*
* @notapi
*/
static inline void init_board(void) {
palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(GPIOD, 12, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(GPIOD, 13, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(GPIOD, 14, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(GPIOD, 15, PAL_MODE_OUTPUT_PUSHPULL);
// Configure the pins to a well know state
SET_RS;
SET_RD;
SET_WR;
CLR_CS;
}
/**
* @brief Set or clear the lcd reset pin.
*
* @param[in] state TRUE = lcd in reset, FALSE = normal operation
*
* @notapi
*/
static inline void setpin_reset(bool_t state) {
(void) state;
/* Nothing to do here - reset pin tied to Vcc */
}
/**
* @brief Set the lcd back-light level.
*
* @param[in] percent 0 to 100%
*
* @notapi
*/
static inline void set_backlight(uint8_t percent) {
(void) percent;
/* Nothing to do here - Backlight always on */
}
/**
* @brief Take exclusive control of the bus
*
* @notapi
*/
static inline void acquire_bus(void) {
/* Nothing to do here since LCD is the only device on that bus */
}
/**
* @brief Release exclusive control of the bus
*
* @notapi
*/
static inline void release_bus(void) {
/* Nothing to do here since LCD is the only device on that bus */
}
/**
* @brief Send data to the index register.
*
* @param[in] index The index register to set
*
* @notapi
*/
static inline void write_index(uint16_t index) {
palWritePort(GPIOE, index);
CLR_RS; CLR_WR; SET_WR; SET_RS;
}
/**
* @brief Send data to the lcd.
*
* @param[in] data The data to send
*
* @notapi
*/
static inline void write_data(uint16_t data) {
palWritePort(GPIOE, data);
CLR_WR; SET_WR;
}
#if GDISP_HARDWARE_READPIXEL || GDISP_HARDWARE_SCROLL || defined(__DOXYGEN__)
/**
* @brief Read data from the lcd.
*
* @return The data from the lcd
* @note The chip select may need to be asserted/de-asserted
* around the actual spi read
*
* @notapi
*/
static inline uint16_t read_data(void) {
uint16_t value;
// change pin mode to digital input
palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_INPUT);
CLR_RD;
value = palReadPort(GPIOE);
value = palReadPort(GPIOE);
SET_RD;
// change pin mode back to digital output
palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
return value;
}
#endif
#endif /* _GDISP_LLD_BOARD_H */
/** @} */