ugfx/drivers/gdisp/SSD1963/gdisp_lld_board_example_fsmc.h
2013-06-15 21:37:22 +10:00

181 lines
5.5 KiB
C

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://chibios-gfx.com/license.html
*/
/**
* @file drivers/gdisp/SSD1289/gdisp_lld_board_example_fsmc.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1289 display.
*
* @addtogroup GDISP
* @{
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
#if defined(GDISP_USE_GPIO)
#define Set_CS palSetPad(GDISP_CMD_PORT, GDISP_CS);
#define Clr_CS palClearPad(GDISP_CMD_PORT, GDISP_CS);
#define Set_RS palSetPad(GDISP_CMD_PORT, GDISP_RS);
#define Clr_RS palClearPad(GDISP_CMD_PORT, GDISP_RS);
#define Set_WR palSetPad(GDISP_CMD_PORT, GDISP_WR);
#define Clr_WR palClearPad(GDISP_CMD_PORT, GDISP_WR);
#define Set_RD palSetPad(GDISP_CMD_PORT, GDISP_RD);
#define Clr_RD palClearPad(GDISP_CMD_PORT, GDISP_RD);
#endif
#if defined(GDISP_USE_FSMC)
/* Using FSMC A16 as RS */
#define GDISP_REG (*((volatile uint16_t *) 0x60000000)) /* RS = 0 */
#define GDISP_RAM (*((volatile uint16_t *) 0x60020000)) /* RS = 1 */
#endif
/**
* @brief Send data to the index register.
*
* @param[in] index The index register to set
*
* @notapi
*/
static inline void write_index(uint16_t index) { GDISP_REG = index; }
/**
* @brief Send data to the lcd.
*
* @param[in] data The data to send
*
* @notapi
*/
static inline void write_data(uint16_t data) { GDISP_RAM = data; }
/**
* @brief Initialise the board for the display.
* @notes Performs the following functions:
* 1. initialise the io port used by your display
* 2. initialise the reset pin (initial state not-in-reset)
* 3. initialise the chip select pin (initial state not-active)
* 4. initialise the backlight pin (initial state back-light off)
*
* @notapi
*/
static inline void init_board(void) {
const unsigned char FSMC_Bank = 0;
#if defined(STM32F1XX) || defined(STM32F3XX)
/* FSMC setup for F1/F3 */
rccEnableAHB(RCC_AHBENR_FSMCEN, 0);
#if defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
#error "DMA not implemented for F1/F3 Devices"
#endif
#elif defined(STM32F4XX) || defined(STM32F2XX)
/* STM32F2-F4 FSMC init */
rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
#if defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
if (dmaStreamAllocate(GDISP_DMA_STREAM, 0, NULL, NULL)) gfxExit();
dmaStreamSetMemory0(GDISP_DMA_STREAM, &GDISP_RAM);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
#endif
#else
#error "FSMC not implemented for this device"
#endif
/* set pins to FSMC mode */
IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 7) | (1 << 8) |
(1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0};
IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
(1 << 13) | (1 << 14) | (1 << 15), 0};
palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_Bank+1] = (FSMC_BTR1_ADDSET_1 | FSMC_BTR1_ADDSET_3) \
| (FSMC_BTR1_DATAST_1 | FSMC_BTR1_DATAST_3) \
| (FSMC_BTR1_BUSTURN_1 | FSMC_BTR1_BUSTURN_3) ;
/* Bank1 NOR/SRAM control register configuration
* This is actually not needed as already set by default after reset */
FSMC_Bank1->BTCR[FSMC_Bank] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
}
static inline void post_init_board(void) {
const unsigned char FSMC_Bank = 0;
/* FSMC delay reduced as the controller now runs at full speed */
FSMC_Bank1->BTCR[FSMC_Bank+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
FSMC_Bank1->BTCR[FSMC_Bank] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
}
/**
* @brief Set or clear the lcd reset pin.
*
* @param[in] state TRUE = lcd in reset, FALSE = normal operation
*
* @notapi
*/
static inline void setpin_reset(bool_t state) {
(void) state;
/* Nothing to do here */
}
/**
* @brief Set the lcd back-light level.
*
* @param[in] percent 0 to 100%
*
* @notapi
*/
static inline void set_backlight(uint8_t percent) {
//duty_cycle is 00..FF
//Work in progress: the SSD1963 has a built-in PWM, its output can
//be used by a Dynamic Background Control or by a host (user)
//Check your LCD's hardware, the PWM connection is default left open and instead
//connected to a LED connection on the breakout board
write_index(SSD1963_SET_PWM_CONF);//set PWM for BackLight
write_data(0x0001);
write_data(percent & 0x00FF);
write_data(0x0001);//controlled by host (not DBC), enabled
write_data(0x00FF);
write_data(0x0060);//don't let it go too dark, avoid a useless LCD
write_data(0x000F);//prescaler ???
}
/**
* @brief Take exclusive control of the bus
*
* @notapi
*/
static inline void acquire_bus(void) {
/* Nothing to do here */
}
/**
* @brief Release exclusive control of the bus
*
* @notapi
*/
static inline void release_bus(void) {
/* Nothing to do here */
}
#if GDISP_HARDWARE_READPIXEL || GDISP_HARDWARE_SCROLL || defined(__DOXYGEN__)
/**
* @brief Read data from the lcd.
*
* @return The data from the lcd
* @note The chip select may need to be asserted/de-asserted
* around the actual spi read
*
* @notapi
*/
static inline uint16_t read_data(void) { return GDISP_RAM; }
#endif
#endif /* _GDISP_LLD_BOARD_H */
/** @} */